[difference from the old model]
・Product design incorporating lines
The design has been renewed by adding a continuous line from the heat radiation fin to the resin part.
・Lid with a stone-like design
We have changed the design to have an impact that changes the common sense of conventional plant growing lights.
・Use parts with high durability
The parts inside the power supply have been changed to more durable ones.

How to remove the reflector is explained using AMATERAS.
[Body color] White
[Color temperature] Approximately 4000K-5000K
[Color Rendering Index] High Color Rendering Ra97

● Density of electric and photon bundles (when the illuminance distance is cm)
[Illuminance] 21690lux
[PPFD] 507 μmol m-2s-1
[Total luminous flux] 2098lm
[Lumen] 2098lm
[Cap] E26
[Base] E26
[Power consumption] 20W
[Low power] 20W
[Complex life (h)] 20000 hours
[Rated life] 20000 hours
* Remaining life is a definition and there is no limit.

● Insert
[Length] 14 cm
[Continued] 12cm
[Mass] 350g
[Compressed voltage (V)] 100-240
[For use] 50-60HZ
[Non-irradiation distance] 40cm-150cm

● 1 This electricity bill
Irradiation for 12 hours a day x 3 days = about 200 yen
(Calculated at 27 yen for 1kWh)

Color rendering properties Color rendering.
Plants and wet plants are more beautiful.
The way plants grow is also in line with the way they grow below.

● Precautions before using this product
* Please be sure to read before purchasing.

● The following equipment cannot be used.
* It may cause damage or malfunction.

○ Never use it with a light bulb fixture or circuit with a remote control.
○ Never use it with an instrument that has a dimming (brightness can be adjusted) function.
(Including step dimmer) (Cannot be used even with 100% lighting)
○ Emergency lighting fixtures, guide light fixtures, HID lamps (mercury lamps, etc.) fixtures,
Never use it with a device with a motion sensor dedicated to incandescent light bulbs.
(In addition, depending on the type of equipment used, it may not be possible to use it due to dimensional, thermal, or other circumstances.)
○ Never use it with heat insulating material construction equipment (SB, SGI, SG type display equipment).
○ Be sure to use equipment that can accommodate more than the wattage of this product.
(If the lamp is 20W, please check if the equipment supports 20W or more.
If not supported, the lamp will fail. )
○ Cannot be used with lighting fixtures with different bases.
○ With a closed type device or a device close to a closed type, the temperature rise will be large, and
Do not use as it will shorten the lamp life. Use open equipment.

● Precautions for use
※Please confirm.

○ Cannot be used outdoors. (Cannot be used even with closed appliances)
○ Do not use in a place where it is exposed to water drops or in high humidity.
○ Since the way the light spreads (light distribution) is different from that of a light bulb,
Types of fixtures (such as fixtures with lamps mounted sideways or diagonally)
Depending on the case, proper light distribution and brightness may not be obtained.
○ Do not use in a place where the ambient temperature of the lamp exceeds 40 °C.
The recommended ambient temperature is (-5 °C to 40 °C). It lights even at (-5 °C or less), but
Since it is not low temperature and waterproof, it cannot be used in an environment where condensation occurs.
○ Use at the indicated voltage.
It may cause a short life or non-lighting.
○ Because there are variations in light color and brightness of LED light sources,
Please note that the light color and brightness may differ even for products with the same model name.
○ Life is the time it takes for the luminous flux to drop to 70%. The indication is the design life,
We do not guarantee the life of the product.
The LED chip will not burn out, but the power supply board will break down depending on the usage conditions.
It may turn off.
○ Place the appliance near a hot object (stove, gas range, etc.) or in a place where humidity is generated.
Please do not use. It may cause fire or electric shock.
■Failures caused by continuous operation for 24 hours are not covered by the warranty.
Continuous operation for 24 hours increases the likelihood of failure. Be sure to rest for 30 minutes every 12 hours. If it has been operated continuously for more than 12 hours, please wait for at least 30 minutes before restarting operation.